세이프원

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

As time passes the handles on your doors will wear out and need to be changed. In this case, it is important that the new handles match the exact dimensions of the old handle.

The top screw's position as well as the lever and keyhole sizes are the three measurements you need to verify. Use the size guide to assist you.

Inline Lever/Lever

A lever handle is a modern-day door handle designed to suit new or replacement doors. This kind of door handle is available in a wide range of designs and finishes. A variety of manufacturers provide this type of handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The handles made of uPVC/Composite are made of tough materials and are ideal for doors with multiple points that require a robust design. The handles are inline and they use the same spindle and screws to fix them. They can be easily installed on a new or existing uPVC/Composite door.

The handle can be adjusted and angled to accommodate all users. The handle has been endurance tested to 200,000 cycles, this helps to ensure the quality of the finish and the performance of the handle over time. The sprung lever can also be shortened to fit a wider range of locks. This is useful for doors with narrower openings where the cylinder is further away from the door. A shortened lever can also be used on doors with latches that can be activated with the thumb located on the inside.

Lever Pad

A Lever Pad upvc door handle operates differently to the lever type handles on doors. These handles are operated by a single spindle or by two spindles, either inline or offset. They are typically used on UPVC doors with double glazing window handle glazing. They come in a variety of finishes & variations.

The handles are available in a variety of finishes including White, Chrome, and Gold. The finish is in line with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, giving the handle a high level of durability and performance for its intended use.

All UPVC handle lever pads come with a spindle, screws, and can be fitted on a uPVC door. The backplate fixing centres of 211mm allow for a wider size handle that can be beneficial when replacing a faulty or worn multi-point door lock mechanism. These levers for handles are also spring-loaded, which solves the issue of handles that slide from their horizontal position when they are not in use.

When choosing the replacement UPVC handle and spindle, it is essential to match the dimensions of the PZ of the multipoint lock as well as the uPVC door. This measurement is often called the handle centre or 'cylinder centres which is a crucial aspect to match the right handles.

After you have identified the correct PZ size, you will need to ensure that the push and lever pads are shaped to fit the American with Disabilities Act compliant handles you require for your door. These are usually round or square with an internal lever and an external push pad.

Most of the UPVC lever pads that we offer are sprung, which means that they return to their horizontal position when not in use, rather than hanging out and possibly securing in the frame. This prevents draughts from entering the property. The majority of UPVC lever pad handles are available in left and right handed versions which allows them to be installed on either side of the doors.

Euro Cylinder

Cylinder locks are commonly found on uPVC doors, but can be utilized on other types of door. They work by using a key that unlock a cylinder that is then revealed with pins that can be aligned with those in the lock body, allowing them to turn an revolving cam, opening the door. Euro cylinders can be fitted with up to six pins. Doors that are internal and external require different levels of security.

The choice of cylinder you choose is vital. It depends on the amount of use your doors and handles will receive. External doors, for instance are required to be fitted with cylinders with greater security while doors inside can be secured with the standard cylinder. Certain cylinders are equipped with additional features that can increase security, like anti-drill or anti-bump properties.

To make sure that the euro cylinder is the right size for your door, it must be measured correctly. The cylinder should be measured from the central screw hole to the ends of the cylinder. This includes the thumb turn, if there is one. If you cannot measure using the lock in its position, you can take it out of it. A cylinder that protrudes beyond the window handle replacement and escutcheon may be susceptible to attacks like snapping locks, therefore it is important to make sure it's not too long.

The design of many modern cylinders has anti-drilling and bump resistance features. They are designed to decrease attack chances by forcing the cylinders to rotate in a new direction. This helps stop the attack and keep your doors safe.

Certain cylinders are constructed to withstand snapping. This is an increasingly common kind of attack on cylinders which is where the break line of the lock is targeted by a tool that is specially designed to break the double glazed front door handles of the cylinder and allow the door to open. This is a quicker and easier way to gain access than the use of a multipoint locking window handle system. It also leaves less evidence of the burglary which can make it difficult to prove insurance claims.

Spring Cassette

The spring cassette is located within the base of your door handle backplate, providing a spring solution and returning your multipoint lock handles to their normal position after usage. Previously a lot of these types of handle did not have a spring integrated into them, and without it they can droop or drop when the locking mechanism has been disengaged. This simple component is the best way to address this issue. It also helps prevent your upvc door from becoming stuck in the closed or open position as they aren't easy to close manually.

The spring cassettes were made to be used with a sprung multipoint locks. They are not compatible with handles that are not sprung and you'll need to cut a hole in your backplate for them to fit. (Please see the image for a technical diagram). They are a replacement for broken or missing cassettes within the backplates of door handles of numerous kinds of uPVC doors. They are sold as one unit. They feature a square cut out that is able to accommodate an 8mm shaft.

These spring cassettes are a fantastic cost-effective solution to the issue of handles on your doors sagging. They are simple to install and will extend the life span of your uPVC doors. Please contact our team to learn more about our wide range of uPVC accessories and spares. We are here to assist and give you expert advice.